Haberler

608 2rs rulman boyutları

608-2RS deep groove bilyalı rulman parameters, brand models, and related specifications are detailed with corrected weight.

608 2RS Bearing Core Parameters (Revised Version)

The following is the detailed parameter and dimension information of the 608-2RS bearing, with the original weight error corrected to ensure data accuracy:
– Bearing Type: Deep Groove Ball Bearing

– Domestic New Model: 608-2RS

– Domestic Old Model: 180018

– Inner Diameter: 8mm

– Outer Diameter: 22mm

– Width: 7mm

– Grease Lubrication Speed: 23000r/min

– Basic Static Load Rating (Cor): 1.35kN

– Basic Dynamic Load Rating (Cr): 3.30kN

– Oil Lubrication Speed: 41000r/min

– Weight: 0.012KG (The original 12KG was a parameter error, which has been corrected here)

608-2RS Bearing Model Comparison Table by Brand

The corresponding models of 608-2RS bearings from different brands are as follows for easy selection and comparison:

SKF: 608-2RS1; NSK: 608DD; FAG: 608.2RSR; NACHI: 608-2NSL; KOYO: 6082RS; RHP: 608-2RS; STEYR: 608-2RS; MRC: 38ZZ; SNR: 608EE

Core Information of 608-2RS Deep Groove Ball Bearing Sample

Summary of Imported Bearing Models with the Same Size (8×22×7)

The following are the models of imported bearings with the same size (8mm inner diameter, 22mm outer diameter, 7mm width) as the 608-2RS bearing:

SKF: 608, 608-2RSH, W 608-2Z, W 608-2RS1, W 608, 608-RSH, 608-2RSL, 608-RSL, 608-2Z/C3WT, 608-2Z, 608-Z;

KOYO: F608ZZ, F608, 608-2RS, 608-2RU, 608ZZ, 608;

NTN: MM-SEB08J1ZZ1C3/0G, 5MG-SEB08J1ZZ1C3/0G, MT2-SEB08J1ZZ1C3/0G, SC850ZZNR, FL608ZZ, FL608Z, FL608, 608ZZ, 608Z, 608;

NSK: 8BGR10X, 8BGR10H, 8BGR10S, 8BSA10T1X, 708A, 708C, 108, F608DD, F608VV, F608ZZ, F608, 608DD, 608VV, 608ZZ, 608;

FAG: 108-TVH, 608-2Z, 608-2RSR, 608;

Other Imported Models: SKF 708 ACD/HCP4AHS, SKF 708 ACD/P4AHS, SKF 708 CD/HCP4AHS, SKF 708 CD/P4AH.

Summary of Domestic Bearing Models with the Same Size (8×22×7)

Below are the models of domestic bearings with the same size (8×22×7) as the 608-2RS bearing, covering different series and precision grades:

HZB: 608-2RDA, SSF608-ZZ, SSF608, SS608-ZZ, SS608, F608-ZZ, F608-Z, F608C3, F608, 608-ZZC3P6QE6, 608-ZZC3, 608-ZZ, 608-ZC3, 608-Z, 608C3, 608;

TG: 108, 608, F608;

Other domestic models: 608HH/YA, 608/P53, 608/P6, 608/P4, 608/P5, 608/C3, 608-Z/C3, 608-Z/P5, 608-2Z/P6, 608-RZ/P5, 608-RZ/P6, 608-2Z/P5, 608-2Z/C2, 608-2Z/C3, 608-2Z/C9, 608-2RZ/P5, 608-2RZ/P6, 108/P5, 108/P6, 608-Z/P6, R-2280HH, 608-2ZWC, B708C/P4, B708C/P5, B708C/P6, 708CJ/P4, 708CJ/P5, 708CJ/P6, 708C/P4, 708CETA/P2, 708CETA/P4.

Detailed Introduction to Deep Groove Ball Bearings

Sabit bilyalı rulmanlar are composed of a pair of races, a set of cages and a set of steel balls. With a simple structure and easy installation, they are one of the most widely produced and used rulman türleri in the world. 608-2RS sabit bilyalı rulman is a typical representative of this type.

The core load-bearing capacity of this type of bearing is mainly radial load, but it can also bear a certain amount of axial load in any direction. When the radial internal clearance of the bearing is increased within a reasonable range, the deep groove ball bearing can have the characteristics of angular contact ball bearings, and then can bear larger axial loads. This is an important performance advantage of 608-2RS bearing in practical application.

After the sabit bilyalı rulman is installed on the shaft, the axial displacement of the shaft or housing can be limited within the axial range of the bearing itself. In addition, when there is a slight inclination between the housing hole and the shaft (or the outer ring and the inner ring) (the inclination angle does not exceed 8′-16′, which is determined according to the bearing clearance), the bearing can still work normally. However, it should be noted that the existence of the inclination angle will shorten the service life of the bearing to a certain extent.